The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
Everybody seems to have their own concepts on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a home handyman's abilities, although you will need an assistant to leave the old tub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the task and also fit trying it. As opposed to working with a professional to take control of a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This post will assist you mount a new bathtub in your bathroom if you have actually already gotten a brand-new tub as well as do not need to change the setup of your previous water supply pipes.
Your tools as well as material list need to comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the water supply. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in area between the faucet and the sink. Secure the tap in place with the maker supplied backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous kind needs to be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Tub
Using both wooden boards under its feet, position the bathtub in the required position. The wood boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the level and changing the feet on the bath tub up until the level reviews level.
To set up taps, fit all-time low of the outermost versatile faucet port to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply and also inspect all joints and new pipework for leaks and tighten them if required. Load the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Finally, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of a minimum of when as this will resolve it right into its final placement.
Preparing for the Setup
Firstly, the supporting structure supplied with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last setting.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, leading to issues with wetness and feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the tub with water prior to sealing, to enable the motion experienced when the tub is in usage. The sealant can break rather very early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
I came across that content about How to Install a Bathtub Yourself while scouting around the web. Sharing is nice. Helping others is fun. Thank-you for going through it.
Book Report this page